The UL325Standard for Safety for Door, Drapery, Gate, Louver, and Window Operators and Systems, Fifth Edition Dated June 7, 2002: The standard was developed by Underwriters Laboratories Inc. in an open non-exclusionary process for manufacturers to use in designing products. This page uses frames, but your browser doesn't support them. Audio alert alarm now needed for all gate operators (previously only required for Class I and II). UL-325 › Historical Revision Information Standard for Door, Drapery, Gate, Louver, and Window Operators and Systems UL-325 - 5TH EDITION - SUPERSEDED Show Complete Document History How to Order Through our network of over 46,000 people in 1,000 laboratories and offices in 100 countries, Intertek provides quality and safety solutions to a wide range of industries around the world. DASMA members of the gate operator industry initiated the inclusion of vehicular gate operator provisions within UL 325 in the early 1990's. Intertek is the industry leader with over 46,000 people in 1,000 locations in over 100 countries. That edition was primarily focused on the electric operation of garage doors and did not contain provisions for gates. Development of UL 325 The first edition of UL 325 was released in 1973. On June 16, 2017, UL notified the Commission that UL published additional revisions to UL 325, Sixth Edition, on May 25, 2017, which became the Seventh Edition. Impact Statement:  A review of all Listing Reports is necessary to determine which products comply with new/revised requirements and which products will require re-evaluation. That edition was primarily focused on the electric operation of garage doors and did not contain provisions for gates. NOTE: Effective immediately, this revised standard will be exclusively used for evaluation of new products unless the Applicant requests in writing that current requirements be used along with their understanding that their listings will be withdrawn on Effective Date noted above, unless the product is found to comply with new/revised requirements. Also revised Instructions for controls for emergency access. Learn More, Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards. NOTE: Additions to existing requirements are underlined and deletions are shown lined out below. After federal laws were enacted in the early 1990s, citing the provisions of UL 325 as applicable to garage door operation, members of the gate operator industry Overview of Changes:  Many clarified, revised and added new paragraphs to reflect the outcome of Standards Technical Panel (STP) meetings and discussions in 2012 and 2013. Learn More. CUSTOMERS PLEASE NOTE: This Table and column "Verdict" can be used in determining how your current or future production is or will be in compliance with new/revised requirements. 5th Edition Revised June 3, 2013 Effective Date of New/Revised Requirements Effective Date (see Schedule below): January 12, 2016 NOTE – Another SUN is still in process with Effective Date of December 23, 2014 which is covered in previous SUN issued October 2012. Learn More, Validating the specifications, value and safety of your raw materials, products and assets. Standard 325, Edition 7 Edition Date: May 19, 2017 DOD Approved: January 21, 1992 ANSI Approved: February 28, 2020 $798.00-$1,990.00 Available in English, Français Purchase Options Get Update Alerts Learn more about UL's Alert Service Those revised requirements are covered below with other requirements with ED = January 12, 2016. Revision to Remove Reference to Terms "Primary" and "Secondary" when Describing Entrapment Protection Devices. ACTION:  Certs to be reviewed to confirm no Vehicular gate operator Class III and IV products are relying on Type E audio alarm entrapment protection. We will do this at no charge as long as Intertek is notified in writing prior to the review of your reports. Door, Drapery, Gate, Louver, and Window Operators and Systems, G Mark Requirements for Electronics Imported to the Gulf Member States, 3.4, 3.11, 3.19, 25.11, 31.1.1, Table 31.1, 31.1.2, 31.1.6, 31.1.7, 31.1.15, 31.2.1.1, 31.2.1.2, 58.1.6. 58.8.4 items a) 2),  item f) and exception. Information – To assist our Engineer with review of your Listing Reports, please submit technical information in response to the new/revised paragraphs noted in the attached or explain why these new/revised requirements do not apply to your product (s). ACTION: Certs to be reviewed to confirm Class III and IV gate operators to ensure they now include audio alert alarm per 31.1.2. Whether your business is local or global, we can ensure your products meet quality, health, environmental, safety, and social accountability standards for virtually any market around the world. Schedule:  So that shipping of products with Listing Marks will not be interrupted, an approximate schedule has been established to ensure Listing Reports are found compliant by Effective Date: Fees:  An initial review of Listing Report (s) will be covered by a direct billing project and will be invoiced at not more than $1000 per report. SUN UL 325 - Doors, Gates, Window Operators, Systems, May 15, 2015 = 8 Month Report Review – Intertek will review all Reports. Clarification of Instructional and Marking Requirements for Installations Less Than 8 Feet Above the Floor. Previous SUN also contained 3 revised requirements (25.11, 31.1.7, Table 31.1) with stated ED = January 12, 2015 then was pushed out to January 12, 2016. Revisions to Instructions for gate operators regarding screening or guarding of horizontal slide gates, to align with ASTM F2200. Removing Type E device (audio alarm entrapment protection device) as an option for Gate Operators. Learn More, Formally confirming that your products and services meet all trusted external and internal standards. UL 325 & ASTM F2200 Safety Standards for Gate Operator Manufactures, Installers & Dealers Required Entrapment Protection Provisions Per UL 325 A key part of the UL 325 standard is a table (Table 31.1) that summarizes the entrapment device options for different classes of operators of the various types of gates included in the standard. Current Listings Not Active? Effective Date (see Schedule below): January 12, 2016NOTE – Another SUN is still in process with Effective Date of December 23, 2014 which is covered in previous SUN issued October 2012. Update if compliance is verified or issue Findings Letter/Quote for any re-evaluations needed, July 17, 2015 = 6 Month Quote Cut-off – Quotes returned for necessary re-evaluations, December 18, 2015 = 30 Day Warning – Client advised of all non-compliant Reports to be Suspended, January 12, 2016 = Effective Date – ATM Suspended for all non-compliant Reports. Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes. What Manufacturers Should Know as We Approach the New Year. Specific details of new/revised requirements that may affect currently ETL Listed products are found in table below. The first edition of UL 325 was released in 1973. – Please immediately identify any current Listing Reports or products that are no longer active and should be removed from our records.

Romans 6:5 Meaning, How To Identify Thrips On Houseplants, Brownian Motion With Drift Hitting Time, Microsoft Company Logo, Highest Paying Psychology Jobs, Restaurant Furniture For Sale Near Me, Johnsonville Polish Sausage Calories, Cement Oxide Colours,